Multicolour Switches HI (Fig.3C)
GB
0/1-2-3 Speed Switches L - Light Switch T - Timer
Introduction
The Timer will run if the timer switch is pushed and will stop running the cooker hood
These instructions are designed to tell you of the various technical details of your
after 5 minutes.
cooker hood and to make you familiar with its use. Since these instructions cover moreSilicon Switches (Fig.3D-E)
than one type of hood within the same series, it may be that reference is made toFIG.3E
components that do not form part of the hood that you are installing. The hood may
+/- Speed Selector2 - Light Switch1 - ON/OFF Switch3 - Display
be used as an exhaust or filter hood. If evacuation is available (exhaust duct or airThe ON/OFF button switch on or off the hood. When the unit is switch OFF and the button
flue) we recommend using the hood in the exhaust version to discharge all the kitchenwill be pressed for more than 2 seconds the motor will start in the last selected speed.
vapors and odors out-doors. Fittings can vary from country to country. We reserve
When the unit is switch ON and the button will be pressed for more than 2 seconds the
the right to modify the product without any notice always with the aim of improvementsTimer will be activated. After 5 minutes the motor will switch OFF, during that time in the
and in compliance with the relevant norm.display is blinking the selected speed.
Suggestions for using the hood in exhaust position
With the button +/- can be changed the speed. When the unit is switch OFF and the button
When an exhaust hood and a heat source requiring ambient air (e.g. gas, oil, coal
- (minus) will be pressed in the display indicate the saturation of the grease filter. When
stoves, etc.) are used at the same time, attention is required because the air necessary
the unit is switch ON and the button + (plus) will be pressed for more than 2 seconds
for combustion is exhausted from the room through the hood and this createsit set the motor into the intensive speed. After 5 Minutes the motor return into the original
depression. There is no such danger when the maximum depression in the room is 0,04
speed, during that time in the display is blinking the maximum speed.
mbar. In this condition no exhaust gas from the heat source is piped. To assure thisFIG.3E
condition, make openings in the room which cannot be closed (doors, windows, etc.
Each button is illuminated during it?s function by a blue LED.
are not sufficient) and through which the air necessary for combustion can freely flow.2 - Light Switch3 - Booster 1 - Speed Switch
Note:?All the exhaust ductwork in the apartment or house should be studied. In case
The Booster button sets the hood for 5 minutes into the maximum speed and than turn
of doubts, get advice or authorization from the person or agency responsible for the
back into the before chosen speed. If any speed button will be pushed for more than
building. When using gas burners, gas ovens, etc. as well as when using the hood in2 seconds the speed will be temporised for 5 minutes and than the unit switch-off
the filter version, these precautions are not necessary. N.B. The efficiency of thecompletely.
exhaust hood decreases as the length of the ducts and number of elbows increase.
Operation light and function of saturation indication for the grease filters
When using the exhaust version, follow these rules: Do not connect the exhaust hood
Switches Fig.3B - The saturation of the grease filter will be indicated automatically
to chimneys, flues, and air ducts serving the room. Before venting into exhaust fluesafter 20 hours by means with flashing of the running speed of the cooker hood. That
and ducts no longer in use, ask for the approval of the person or agency responsiblemean the grease filter should be cleaned or eventual changed.
for the building. The evacuated air must not be let into a warm air duct. For the evacuation
It is as well possible to select manual the degree of saturation. By switch off cooker
of the exhausted air please note ufficial instructions.hood and pushing the bottoms 1 and 3 temporary for more than 2 seconds:
Installation- No flashing light of the bottom: less than 6 working hours
The hood must be mounted over the center of the cooking area. The minimum distances
- Flashing light of bottom 1: between 6 and 12 working hours
between the cooking area and the underpart of the hood are 650 mm.
- Flashing light of bottom 1 and 2: between 12 and 18 working hours
N.B. The distances, however, are subject to the safety rules in effect in the various
- Flashing light of bottom 1, 2 and 3: more than 18 working hours
countries.After you have cleaned or eventual changed the grease filter you should reset the
Warning: If the room contains a flued fuel burning appliance which is not of the "balance
timer by means pushing the main switch for more than 2 seconds. If the Timer will not
flue" type make sure these is an adequate air inlet to the room at all times so that fumes
by reset manual the electronic will reset after 15 minutes automatically the Timer.
are not drawn down the flue. Before drilling the wall make sure that no pipes or cables
If your cooker hood is supplied with a charcoal filter and is running in the filtering method
will be damaged. If there is no outer waste-pipe for the exhaust version, an air outletthe saturation of the charcoal filter will be indicated. After 120 hours all buttons except
with a diameter of O160mm, in case you use the spigot reduction (Fig.6/H) you need an
the main switch will flashing and the charcoal filter should be replaced.
exhaust outlet of 130mm.
It is as well possible to select manual the degree of saturation. By switch off cooker
Attention: Take attention that the wallwill support the weight of the cookerhood (abouthood and pushing the bottoms 2 and 3 temporary for more than 2 seconds:
30 Kg). The screws supplied with this rangehood are designed for fixing to reinforced- No flashing light of the bottom: less than 30 working hours
concrete, masonry walls or hollow building blocks.
- Flashing light of bottom 1: between 30 and 60 working hours
Wall fixing of the cooker hood
- Flashing light of bottom 1 and 2: between 60 and 110 working hours
1) Set the distance between the cooker hob and the hood (Pict. 5).- Flashing light of bottom 1, 2 and 3: more than 110 working hours
2) If your hood is fitted with a metal carbon filter frame the mounting operation canAfter you have replaced the charcoal filter you should reset the timer by means pushing
be made more easily by removing it by means of the screws (Pict. 2/1) before
the main switch for more than 2 seconds. If the Timer will not by reset manual the
beginning to work. The frame must be remounted when the operation is finished.
electronic will reset after 15 minutes automatically the Timer.
3) Join the two parts of the spigot (Pict. 6/H) and fix it to the upper part of the motorSwitches Fig.3C - The saturation of the grease filter will be indicated by the operation
group (Pict. 6/L) by means of the 4 screws (Pict. 6/I).
LED. By switch off cooker hood and pushing the bottom T the operation LED will indicate
4) Drill the holes into the wall (Pict. 6/N) at the right distance showen here after, and
different colours with following meanings:
fix the cookerhood (Pict. 5).
Green Light: less than 6 working hours
5) For a correct installation the hood is provided (in the rear side of its body) with oneYellow Light: between 6 and 12 working hours
or two holes 8 mm diam. into which one or two wall fixing screws must be inserted
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual
(Pict. 6/O).
changed)
6) For the exhaust version, please connect the flange to an outlet ducting of 125 mm
Switches Fig.3D - By switch off cooker hood and pushing the button - (minus) the display
diameter (Pict. 6/F). If the hood is in recirculating version the flange must be fixedwill indicate the saturation of the grease filter:
to the connection piece, which is provided (Pict. 6/G).- 1 - operation time between 5 and 10 hours
Insure that all parts are properly fixed and that it is impossible to touch moving parts.
- 2 - operation time between 10 and 15 hours
N.B.: When using a 150mm air outlet, do not fasten the air outlet pipe with the screws,- 3 - operation time between 15 and 20 hours
as this might cause the metal valve to malfunction.- 4 - operation time between 20 and 25 hours
N.B.: In the case of recirculation fitting, join the flange and the T joint provided with
- 5 - operation time between 25 and 30 hours
2 screws at the point marked with a line on the flange; this must all be done before
- 6 - more than 30 hours
fixing the hood to the wall.Each time you switch off the hood the saturation of the grease filter will shown for 5
Installation of the pipes (valid for exhaust or filter version)seconds.
1) Fix the bracket (Pict. 6/C) with 2 plugs and screws (Pict. 6/A) in the required hight
After you have cleaned or eventual changed the grease filter you should reset the
for the pipe.
timer by means pushing the button - (minus) for more than 5 seconds.
2) Screw the short pipe (Pict. 6/D) with 2 screws on the bracket (Pict. 6/B).Switches Fig.3E - The saturation of the grease filter will be indicated by the
3) Insert the 2 nuts in the holes on the lower part of the long pipe. Put the long pipe
operation LED. By switch off cooker hood and pushing the Booster button (Fig.3/
over the short one (Pict. 6/E) by pulling a part the laterals of the pipe.3E) the operation LED will indicate the saturation of the grease filter with following
4) Fix the long pipe with 2 screws on the hood (Pict. 6/Q).
meanings:
Attention: The panel should be fitted (if supplied) over the body after installation and- illumination of the button ON/OFF: less than 6 working hours
fixed from the outside using the special screws, washer and cover provided (Fig. 4/
- illumination of the button 2: between 6 and 18 working hours
3). Some models could be supplied only with 2 external and 2 internal fixingpoints with
- illumination of the button 3: more than 18 working hours
relevants nuts (Fig. 4/4). The crystal cover panels are only fixed from the outside.
Each time you switch off the hood the saturation of the grease filter will shown for 5
Electric connectionseconds.
Make sure the supply voltage ratings correspond with those stated on the applianceAfter you have cleaned or eventual changed the grease filter you should reset the timer
data plate.
by means pushing the Booster button for more than 5 seconds.
Attention: if the appliance is not provided with a plug or cannot be easily connectedSetting from Exhaust method into Filtering method (only for model HR - Fig.3B)
to a wall socket, then the electrical circuit must incorporate a circuit breaker havingTo get an efficiency aspiration the cooker hood could work in 2 different methods -
at least a 3 mm separation between contacts. If the appliance is provided with a supply
Exhaust / Filtering. By setting the cooker hood into the proper method the electronic
cord and plug, the appliances must be positioned so that the plug is accessible.will adjust automatically the fan speed to the air resistance of the charcoal filter.
Attention: if there are three wires in the electrical supply cable they must be connectedExhaust Method: By switch off cooker hood and pushing the bottom 1 for more than
as follows:
3 seconds the cooker hood will set to the exhaust method - confirm by flashing all
green/yellow = ground ? blue = neutral ? brown = line
buttons for 4 times.
Important: the hood manufacturer will not be responsible for any damage or loss
Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than
caused by failure to observe these instructions.3 seconds the cooker hood will set to the filtering method - confirm by flashing all
Important: a damaged power supply cord must be replaced by the service.
buttons for 8 times.
Using the cooker hoodNote: The cooker hood is set from the factory into the Exhaust method.
The cooker hood should be switched on either before or at the same as cooking or
Lamp Replacement
frying commences. The grease and carbon filters are more effective if the fan is notWhen the tubolar neon lamps need to be replaced this must only be done by
switched off immediately after cooking or frying is completed, but only after a period
a competent electrician because especiale tool is required. To changes low
of some 20-30 minutes. Before using the cooker hood please ensure that all plastic
energy neon lamps and incandescent bulbs please work from outside of the hood
films like on metal grease filter an stainless steel ducting are removed.
User instructionsmeans to pull off the lamp diffuser. If it has a halogen lamp look out not to
The cooker hood could be supplied with different operation panels (Fig. 3A-3B-3C) thattouch it with your hands when you replace it. Use a dry and not greasy protection
works in the following way:(for example a cloth) in order to avoid a direct contact with skin which could
Mechanical Switches (slide or pushbutton-Fig.3A)make the lamp break. Never use lamps with a wattage higher than the one shown
1 - Speed Switch 2 - Light Switchon the label inside the hood.
Back Lit Switches HR (Fig.3B)Safety rules
- Main Switch1-2-3 Speed SwitchesDo not do any flambe cooking underneath the hood. When frying, never leave
2 - Light Switchthe pan alone because the cooking oil could flare up. Clean all the surfaces
The Timer will run if any speed switch is pushed for more than 3 seconds and will stopfrequently to avoid danger of fire. This can be done with a cloth or/and with
running the cooker hood after 5 minutes.a brush drenched with denatured alcohol or with any other similar substances,
10401250370 |
ACEC
