make the electrical connection. It is advisable to call a qualified technician to the hood. voltage indicated on the label affixed inside the house voltage corresponds with the Before completing any connection make sure Electric connectionor mixed-fuel burners. above electric burners or 75 cm above gas and burners must be not less than 65 cm When installed, the distance between hoodInstallationis impossible to install one. haust duct for venting outdoors or when it This version is used when there is no ex-mounted.filter, then it must be ordered andIf the hood is not supplied with carbonAttention! chimney. through the grating on the lower side of the bon filter�) and recirculated into the room (for its installation see paragraph OCar- The air is filtered through a carbon filter Filter version (K)+(S)then it must be removed. If the hood is supplied with carbon filter Attention!to the outside.upwards to vent the air easily from the roomslightly slanted (about 10In the horizontal runs the duct must beequal to that of the connection ring.Diameter of the exhausting pipe must benection ring above the hood.exhausting pipe that is affixed to the con-Vapours are extracted outside through anExhaust mode (K)+(S)Use:3) Worktop illumination 2) Metal grease filter 1) Control panelHood Description
Two systems are available
- Fig. 1
°
) and directed
GB
6
��� Warning!��Using the hoodthe supports (Fig. 4). adjacent cabinets and place the shelf on Fasten the four side supports Fastening of shelves (optional)observer the above instructions. problems caused by the user The manufacturer is not liable for anynot less than 3mm. switch with a minimum contact opening of Fit an approved plug or an approved bipolarAppliance without plug 3mm. a minimum contact opening of no less than essary to fit an approved bipolar switch with inserted in the socket, it will however be nec- If the plug is not accessible once it has been tact opening of no less than 3mm. proved bipolar switch with a minimum con- tric mains, remove the plug and fit an ap- If you intend to connect it directly to the elec- current regulations. Connect it to a socket which conforms withAppliance fitted with plug
gerous for the filters and could cause fires. The use of an unprotected flame is dan- neath the hood. No food must be cooked flambŽ under- must be made for an adequate air supply. sources other than electricity, provision of other appliances that run on energy When the hood is used at the same time sources other than electricity. of other appliances that run on energy The hood cannot be connected to flueseliminated. it running until all the odours have been few minutes before cooking and keeping We recommend starting up the hood a vapour concentration. in particular cases of strong odour and in normal conditions and the high speeds ce, we recommend using the low speeds several speeds. For the best performan- The hood is provided with a motor with
Os failure to
I
to the
d)c) b) a)Mounting and replacing the carbon filter: normal use. It should be changed every 4 months with The carbon filter must never be washed. This filter dissolves cooking odours. Carbon filter (2 pieces)put the filters back after having washed them. Carry out the above steps in reverse orde, to putting it back into place. Let the filter dry without damaging it before backwards and then downwards (Fig. 2). gned for this purpose by pulling the filter Remove the filter using the handles desi- least once a month. The grease fiilters must be washed at dishwasher must be washed either by hand or in the The metal grease filter lasts forever and Metal grease filter (2 or 3 pieces)must be removed from the socket. through a plug and socket, then the plug Or if the appliance has been connected removing the connector fuse. supply by switching off at the connector and tion, isolate the hood from the electrical Before performing any maintenance opera-Maintenance��
If the charcoal filters have already been filters in the clockwise direction (Fig. 3). motor. Then turn the center handle for the the grates protecting the rotor on the one filter on each side so that they cover If the filters have not been installed, place Remove the metal grease filters (Fig. 2). Disconnect the hood from the electricity.observe the above instructions. its catching on fire because of failure to responsibility for damage to the hood or The manufacturer refuses to accept any discharge. directives regarding the question of fume Please, keep to the provisions of official could flare up. the pan alone because the cooking oil the hood. When frying foods, never leave Therefore, never use an open flame under
(65
°
C)
with suitable detergents.
GB
7
e) d)c) b) a) Replacing the lampinstructions. Therefore, we recommend observing these filters can cause fires. appliance and changing and cleaning the Failure to observe the rules for cleaning the Attentiondirection as the brushing to avoid scratching. Wipe brushed stainless steel in the same taining abrasive. liquid detergents. Never use products con- moistened with denatured alcohol or neutral To clean the outside of the hood use a cloth Cleaninge)
bulbs are screwed in tightly. the hood fails to light up, make sure the Before calling for repair service because Refit the the metal grease filters. (Fig. 7). 20 Watt max. (Fig. 6) and 11 Watt max. lamps with 40 Watt max. (E14) (Fig. 5) - Illumination: always replace burnt-out Remove the grease filters (Fig. 2). Disconnect the hood from the electricity.Refit the metal grease filters. are unlocked. counter-clockwise direction until the filters replaced, turn the central handle in the the rotor on the motor) and must be installed (covering the grates protecting |
ACEC
